[an error occurred while processing this directive] [an error occurred while processing this directive] [an error occurred while processing this directive]
[an error occurred while processing this directive]

弹箭与制导学报 >

2023 , Vol. 43 >Issue 1: 41 - 47

DOI: https://doi.org/10.15892/j.cnki.djzdxb.2023.01.006

装药长径比对杆式射流成型与侵彻性能影响的数值模拟研究

  • 杨世全 ,
  • 王守乾 ,
  • 冯高鹏
展开
  • 中国工程物理研究院总体工程研究所,四川 绵阳 621999

杨世全(1973—),男,高级工程师,硕士,研究方向:常规战斗部研制。

收稿日期: 2022-01-09

  网络出版日期: 2025-02-01

收起

The Numerical Simulation Investigation on the Influence of Length-diameter Ratio of Charge on Jetting Projectile Charge Forming and Penetration Performance

  • YANG Shiquan ,
  • WANG Shouqian ,
  • FENG Gaopeng
Expand
  • Institute of Systems Engineering, China Academy of Engineering Physcics, Mianyang 621999, Sichuan, China

Received date: 2022-01-09

  Online published: 2025-02-01

Fold

摘要

为探索射流成型机理,针对某等壁厚球缺型药型罩结构,开展了不同装药长径比下杆式射流成型和侵彻混凝土靶的数值模拟研究;结合射流成型理论,从装药爆轰波成长角度,分析了装药长径比对杆式射流成型和侵彻性能的影响。结果表明,在装药长径比由0.5增加到0.9时,装药长径比增加可显著提高射流性能,但当装药长径比超过1.0时,作用到药型罩上的压力的增加幅度明显低于装药质量增加幅度,此时装药长径比的增加对射流成型的贡献逐渐减弱。在受限战斗部质量和空间,且为中心一点起爆条件下,可优选装药长径比为0.9或1.0。

关键词： 装药长径比; 杆式射流; 球缺罩; 爆轰波; 数值模拟

本文引用格式

杨世全 , 王守乾 , 冯高鹏 . 装药长径比对杆式射流成型与侵彻性能影响的数值模拟研究[J]. 弹箭与制导学报, 2023 , 43(1) : 41 -47 . DOI: 10.15892/j.cnki.djzdxb.2023.01.006

Abstract

To explore the mechanism of jetting forming, the numerical simulation investigation on jetting projectile charge(JPC) forming and penetrating concrete targets with different length-diameter ratio of charge were conducted based on the hemispherical liner structure with equal thickness. Combining with the theory of jetting forming, the influences of length-diameter ratio of charge on JPC forming and penetration performance were analyzed from the perspective of charge detonation wave growth. The results show that the increase of length-diameter ratio of charge can significantly improve jetting performance when it increases from 0.5 to 0.9, but when length-diameter ratio of charge exceeding 1.0, the increase scope of pressure on the liner is obviously lower than the increase scope of charge mass, and the contribution of the increases of length-diameter ratio of charge to jetting forming is gradually reduced. The optimization of length-diameter ratio of charge is 0.9 or 1.0 under the condition of limited warhead mass and space and central point initiation.

Key words： length-diameter ratio of charge; jetting projectile charge(JPC); hemispherical liner; detonation wave; numerical simulation

[an error occurred while processing this directive]

参考文献

原文顺序 | 文献年度倒序 | 文中引用次数倒序
[1]
黄正祥. 聚能杆式侵彻体成型机理研究[D]. 南京: 南京理工大学, 2003.

HUANG Z X. Mechanism study on jetting projectile charge formation[D]. Nanjing: Nanjing University of Science and Technology, 2003.

[2]
BLACHE A. WEIMAN K. Shaped charge with jetting projectile for extended targets[C]// IBS. Proceedings of the 17th International Symposium on Ballistics. Nevada: ISB, 1998: 207-215.

[3]
MATISSON K, SORENSEN N. Development of the K-charge a short L/D shaped charge[C]// IBS. Proceedings of the 18th International Symposium on Ballistics. Nevada: ISB, 1999:528-534.

[4]
MUR M J. KUKLO R M. Fundamentals of shaped charge penetration in concrete[C]// IBS. Proceedings of the 18th International Symposium on Ballistics. Nevada: ISB, 1999: 1057-1064.

[5]
WHELAN A J, FURNISSS D R, TOWNSLEY R G. Experimental and simulated (analytical & numerical) elliptical form shaped charges[C]// IBS. Proceedings of the 20th Inernational Symposium on Ballistics. Nevada: ISB, 2002:446-454.

[6]
吴晗玲, 段卓平, 汪永庆. 杆式射流形成的数值模拟研究[J]. 爆炸与冲击, 2006, 26(4): 328-332.

WU H L, DUAN Z P, WANG Y Q. Simulation investigation of rod-like jets[J]. Explosion and Shock Waves, 2006, 26(4): 328-332.

[7]
李伟兵, 王晓鸣, 李文彬, 等. 环形多点起爆精度对聚能杆式侵彻体成型的影响[J]. 爆炸与冲击, 2010, 30(1): 45-50.

LI W B, WANG X M, LI W B. et al. Effects of annulus multi-point initiation precision on formation of jetting projectile charge[J]. Explosion and Shock Waves, 2010, 30(1): 45-50.

[8]
段卓平, 温丽晶, 申健, 等. 聚能装药用多点环形起爆器的设计[J]. 兵工学报, 2011, 32(1): 101-105.

DUAN Z P, WEN L J, SHEN J, et al. Design multi-point ring initiator for shape charge[J]. Acta Armamentarii, 2011, 32(1): 101-105.

[9]
徐文龙, 王成, 徐斌, 等. 新型聚能装药爆炸成型杆式射流数值模拟及试验研究[J]. 北京理工大学学报, 2017, 37(6): 579-583.

XU W L, WANG C, XU B, et al. Numerical simulation and experimental investigation on new type jetting projectile charge[J]. Transactions of Beijing Institute of Technology, 2017, 37(6): 579-583.

[10]
徐斌, 王成, 徐文龙. 高速杆式射流形成的数值模拟与实验研究[J]. 北京理工大学学报, 2018, 38(4): 331-337.

XU B, WANG C, XU W L. Numerical simulation and experimental investigation on hypervelocity jetting projectile charge formation[J]. Transactions of Beijing Institute of Technology, 2018, 38(4): 331-337.

[11]
李伟兵, 王晓鸣, 李文彬, 等. 装药长径比对聚能杆式侵彻体成型的影响[J]. 弹道学报, 2011, 23(4): 61-65.

LI W B, WANG X M, LI W B, et al. Effects of length-diameter ratio of charge on jetting projectile charge forming[J]. Journal of Ballistics, 2011, 23(4): 61-65.

[12]
张万君, 李国辉, 王凯琳, 等. 装药长径比对半球形聚能装药射流成型的数值模拟[J]. 火炸药学报, 2017, 40(5): 98-101.

DOI

ZHANG W J, LI G H, WANG K L, et al. Numerical simulation on the jet formed by hemispherical shaped charge with length-to-diameter ratio of charge[J]. Chinese Journal of Explosives & Propellants, 2017, 40(5): 98-101.

[13]
崔魁文, 高敏, 米双山. 装药长径比对杆式射流成型影响数值分析[J]. 兵工自动化, 2018, 37(12): 81-84.

CUI K W, GAO M, MI S S. Numerical analysis of fitness ratio influence on jetting projectile charge[J]. Ordnance Industry Automation, 2018, 37(12): 81-84.

[14]
杨世全, 王洪波, 郭峰, 等. 起爆直径对杆式射流成型与侵彻的数值模拟[J]. 工程爆破, 2020, 26(6): 28-34.

YANG S Q, WANG H B, GUO F, et al. Numerical simulation of detonation diameters on jetting projectile charge forming and penetration performance[J]. Engineering Explosive, 2020, 26(6): 28-34.

[15]
杨世全, 拜云山, 郭锋, 等. 基于正交试验方法的杆式射流成型和侵彻性能影响因素敏感性分析[J]. 振动与冲击, 2021, 40(11): 240-247.

YANG S Q, BAI Y S, GUO F, et al. Sensitivity analysis of factors affecting the formation and penetration performance of rod jet based on orthogonal test method[J]. Journal of Vibration and Shock, 2021, 40(11): 240-247.

[16]
JOHNSON G R, COOK W H. A constitutive model and data for metals subjected to large strains, high strain rates and high temperatures[C]// IBS. Proceedings of the 7th International Symposium on Ballistics. Nevada: ISB, 1983: 541-547.

[17]
HALLQUIST J. LS-DYNA keyword user’s manual[M]. California: Livermore, 2003.

[18]
时党勇, 李裕春, 张胜民. 基于ANSYS/LS-DYNA 8.1进行显示动力分析[M]. 北京: 清华大学出版社, 2005: 328.

SHI D Y, LI Y C, ZHANG S M. Explicit dynamics analysis based on ANSYS/LS-DYNA 8.1[M]. Beijing: Tsinghua University Press, 2005: 328.

[19]
杨秀敏. 爆炸冲击现象数值模拟[M]. 合肥: 中国科学技术大学出版社, 2010: 334-335.

YANG X M. Numercial simulation for explosion and phenomena[M]. Hefei: University of Science and Technology of China Press, 2010: 334-335.

[20]
黄正祥. 聚能装药理论与实践[M]. 北京: 北京理工大学出版社, 2014: 380.

HUANG Z X. Theory and practice of shaped charge[M]. Beijing: Beijing Institute of Technology Press, 2014: 380.

[21]
HOLMQUIST T J, JOHNSON G R, COOK W H et al. A computational constitutive model for concrete subjected to large strains, high strain rate,and high pressures[C]// IBS. Proceedings of the 14th International symposium on ballistics. Nevada: ISB, 1993: 591-600.

Options
文章导航

/

〈 〉

[an error occurred while processing this directive]