[an error occurred while processing this directive] [an error occurred while processing this directive] [an error occurred while processing this directive]
[an error occurred while processing this directive]

弹箭与制导学报 >

2022 , Vol. 42 >Issue 4: 119 - 124

DOI: https://doi.org/10.15892/j.cnki.djzdxb.2022.04.022

某固体火箭发动机喷管传热烧蚀数值模拟

  • 白涛涛 1 ,
  • 孙振华 1, 2
展开
  • 1 中国空空导弹研究院,河南 洛阳 471009
  • 2 航空制导武器航空科技重点实验室,河南 洛阳 471009

白涛涛(1983—),男,河南洛阳人,高级工程师,硕士,研究方向:固体火箭发动机设计与仿真。

收稿日期: 2021-12-19

  网络出版日期: 2025-05-29

收起

Numerical Simulation on Heat Transfer and Ablation for the Nozzle of a Solid Rocket Motor

  • BAI Taotao 1 ,
  • SUN Zhenhua 1, 2
Expand
  • 1 China Airborn Missile Academy, Luoyang 471009, Henan, China
  • 2 Aviation Key Laboratory of Science and Technology on Airborne Guided Weapons, Luoyang 471009, Henan, China

Received date: 2021-12-19

  Online published: 2025-05-29

Fold

摘要

针对某固体火箭发动机喷管,采用商用CFD软件二次开发功能编写传热烧蚀计算程序,建立喷管扩张段传热烧蚀计算方法,开展了喷管流-固-热耦合数值计算研究,得到了不同时刻喷管扩张段密度、比热容、导热系数及静温变化情况,预估了喷管扩张段体积烧蚀、表面烧蚀及外壁温度随时间变化规律,并与试验结果进行了对比分析。结果表明:碳/酚醛扩张段上的表面烧蚀主要集中在靠近喉衬的左半区,并且主要由发动机一级高压工作段引起;扩张段体积烧蚀质量损失率在发动机初始工作时最大,随后逐渐减小。

关键词： 固体发动机; 喷管; 传热; 烧蚀; 碳/酚醛

本文引用格式

白涛涛 , 孙振华 . 某固体火箭发动机喷管传热烧蚀数值模拟[J]. 弹箭与制导学报, 2022 , 42(4) : 119 -124 . DOI: 10.15892/j.cnki.djzdxb.2022.04.022

Abstract

Aim at the nozzle of SRM, the heat transfer and ablation are programmed using the secondary development function of commercial CFD software, the calculation method of heat transfer and ablation for nozzle divergent is developed, and the fluid-solid-thermal coupling numerical calculation of nozzle is carried out, the density, specific heat capacity, thermal conductivity and temperature of nozzle divergent under different times are obtained, the variation of volume ablation, surface ablation and outside wall temperature with time for nozzle divergent are estimated, and comparisons are made between simulation and test results. It shows that: the surface ablation of divergent is centred on the left half that is close to throat, which is generated by the high pressure working section of SRM; the mass loss rate of volume ablation for nozzle divergent is the largest in the initial stage of working process for SRM, and then it gradually decreases.

Key words： solid rocket motor; nozzle; heat transfer; ablation; carbon phenolic

[an error occurred while processing this directive]

参考文献

原文顺序 | 文献年度倒序 | 文中引用次数倒序
[1]
张研, 齐歆, 郭建忠, 等. 基于烧蚀理论的固体火箭发动机热结构传热数值模拟[J]. 机械制造, 2013, 7(51):27-31.

[2]
张涛, 孙冰. 三维烧蚀内部热响应数值计算研究[J]. 宇航学报, 2012, 33(3):298-304.

[3]
刘建军, 李铁虎, 郝志彪. 喉衬热环境与碳/碳复合材料的烧蚀[J]. 宇航材料工艺, 2005, 35(1):42-48.

[4]
杨德军, 李旭东. C/C复合材料的热化学烧蚀和温度场耦合分析[J]. 复合材料学报, 2013, 30(2):213-219.

[5]
杨德军, 李旭东. 烧蚀条件下C/C复合材料温度场的数值模拟[J]. 计算机仿真, 2013, 30(4):411-415.

[6]
LACHAUD J, COZMUTA I, MANSOUR N N. Multiscale approach to ablation modeling of phenolic impregnated carbon ablators[J]. Journal of Spacecraft and Rockets, 2010, 47(6): 910-921.

[7]
BIANCHI D, NASUTI F. Thermochemical erosion analysis of carbon-carbon nozzles in solid-propellant rocket motors: AIAA 2010-7075[R]. Reston: AIAA, 2010.

[8]
闫宝任, 史宏斌, 唐敏, 等. 背壁热解效应对喉衬组件温度场的影响[J]. 弹箭与制导学报, 2015, 35(4):101-105.

DOI

[9]
BIANCHI D, NASUTI F, ONOFRI M. Thermochemical erosion analysis for graphite/ carbon-carbon rockets nozzles[J]. Journal of Propulsion and Power, 2011, 27(1): 197-205.

[10]
BIANCHI D, NASUTI F, ONOFRI M. Radius of curvature effects on throat thermochemical erosion in solid rockets motors: AIAA 2012-0533[R]. Reston: AIAA, 2012.

[11]
张晓光, 王长辉, 刘宇, 等. 固体火箭发动机碳基材料喷管热化学烧蚀特性[J]. 推进技术, 2012, 33(1):93-97.

[12]
尚永腾. 烧蚀台阶现象及对喷管性能的影响分析[J]. 航空兵器, 2015(3):44-47.

[13]
郑晓亚, 王卫祥, 蔡飞超, 等. 固体火箭发动机喷管热结构一体化计算[J]. 航空动力学报, 2012, 27(9):2122-2127.

[14]
郝雯, 马聪慧, 绍跃跃. 高速旋转固体火箭发动机喷管受热状态计算[J]. 航空兵器, 2015(2):42-49.

[15]
陈长国, 孙娜, 黄永恒, 等. 长尾喷管后效瞬态传热特性分析[J]. 上海航天, 2019, 36(增刊1):62-67.

[16]
薛海峰, 陈雄, 周长省. 基于热解过程的变热物性碳/酚醛能量扩散数值研究[J]. 固体火箭技术, 2015, 38(1):130-135.

[17]
薛海峰, 陈雄, 周长省. 碳/酚醛燃气舵热化学烧蚀过程数值研究[J]. 推进技术, 2016, 37(10):1900-1908.

Options
文章导航

/

〈 〉

[an error occurred while processing this directive]