[an error occurred while processing this directive] [an error occurred while processing this directive] [an error occurred while processing this directive]
[an error occurred while processing this directive]

Journal of Projectiles, Rockets, Missiles and Guidance >

2015 , Vol. 35 >Issue 4: 73 - 76

DOI: https://doi.org/10.15892/j.cnki.djzdxb.2015.04.018

PROJECTILES TECHNOLOGY

Effect of Wave-shaper on the Performance of the Sub-hemisphere Shaped Charge

  • LI Yunlu ,
  • YIN Jianping ,
  • LIU Tongxin ,
  • YI Jianya
Expand
  • School of Mechatronic Engineering, North University of China, Taiyuan 030051, China

Received date: 2014-08-07

  Online published: 2025-05-26

Fold

Abstract

In order to study effects of wave-shaper on jetting projectile charge of sub-semisphere shaped charge, the AUTODYN-2D software was used to simulate formation of projectile. The results show that jet velocity and charge's energy transformation rate have been improved obviously with the wave-shaper. According to analysis on the effect of wave-shaper parameters diameter d and wave-shaper bottom from the liner top distance H of two factors on jet molding by orthogonal design method, the wave-shaper diameter d is the main influencing factor, and H should not too large. The impacts of five wave-shaper materials on jet formation including polyurethane, rubber, nylon, teflon and polystyrene were analyzed by comparison, it shows that the best material is nylon.

Key words： K-charge; wave-shaper; numerical simulation; orthogonal design

Cite this article

LI Yunlu , YIN Jianping , LIU Tongxin , YI Jianya . Effect of Wave-shaper on the Performance of the Sub-hemisphere Shaped Charge[J]. Journal of Projectiles, Rockets, Missiles and Guidance, 2015 , 35(4) : 73 -76 . DOI: 10.15892/j.cnki.djzdxb.2015.04.018

[an error occurred while processing this directive]

References

[1]
谭多望, 孙承纬. 成型装药研究新进展[J]. 爆炸与冲击, 2008, 28(1):50-55.
[2]
李向荣. 巡航导弹目标易损性与毁伤机理研究[D]. 北京: 北京理工大学, 2006.
[3]
廖海平, 黄正祥, 张先锋, 等. 亚半球罩聚能装药的杆式射流特性研究[J]. 弹箭与制导学报, 2008, 28(6): 91-94.
[4]
张先峰, 陈惠武. 三种典型聚能射流侵彻靶板数值模拟[J]. 系统仿真学报, 2007, 19(19): 4399-4401.
[5]
姚志华, 王志军, 王向东, 等. 紧凑型聚能装药射流成型的数值模拟[J]. 弹箭与制导学报, 2012, 32(5): 79-82.
[6]
付建平, 陈智刚, 侯秀成, 等. 罩顶药高对有隔板聚能装药的影响[J]. 弹箭与制导学报, 2013, 12(6): 70-73.
[7]
唐蜜, 杨劲松, 李平, 等. 爆炸成型弹丸成型因素的正交设计研究[J]. 火工品, 2006(5): 38-40.
[8]
ANSYS AUTODYN User Manual: Release 12.1[M]. ANSYS In, 2009.
[9]
尹建平, 王志军. 弹药学[M]. 北京: 北京理工大学出版社, 2012.
Options
Outlines

/

〈 〉

[an error occurred while processing this directive]